Suggested Questions/Answers :
It is recommended you read all this kind of situations
The ice maker is not making ice, the water valve is not getting the DC signal, the icemaker level was turned on and off and still not state change on the water solenoid.. kenmore model # 253.73072300
Kenmore 64802 Top Freezer Refrigerator
I have a Kenmore fride with icemaker.
The icemaker is not working. I can still get water at a full flow.
Model 106 9550780
Serial Se 5112379
Top Mount Kenmore Refrigerator Model # 363.9731785
Ice Maker stopped working.
I've verified that water is getting to the refrigerator (copper) and that the clear plastic water line to the icemaker is not clogged or iced shut.
My guess is that the problem is in/with the blue plastic part between the copper and the plastic (with electric leads and a ground wire attached).
Is this likely? Is it easily replaceable?
HI. First, you will need to rule out any standard issues that will cause this. Check the internal, and external feed lines for any obstructions. Make sure that the internal lines are not frozen, or kinked. If the lines check out ok, move on to the wa ...
I have a Kenmore side by side #52552. Water came pouring out of the icemaker, inside the freezer, and was leaking out through the dispenser.
The water dispenser works fine
The rake arms work fine
Since cleaning everything up, no more water is getting to the icemaker.
Also, the middle plate between the fridge and freezer is hot--but this has been true for awhile without disrupting the icemaker.
Why is water getting to the dispenser but not to the icemaker?
Hi Patti,A couple of things could be going on here. I will assist with trouble shooting if you are up for it.First of all, the hot rail between the freezer and fresh food sections concerns me. This is an indication that the co ...
Kenmore 56539 / 56532 / 5653 / 656534 Side by Side Refrigerator
Kenmore Model #70162990 the icemaker is not getting water, the supply line to the refrigerator is good.
You say you have good pressure to the supply line? Follow the line into the back to a valve, One of tow things is going on. the valve is bad, or the control circuit is not supplying voltage to it. You can check the Ohm's of the valve by - unpul ...
Kenmore model # 106 626636 Icemaker doesn't work it cycles like it should and I can use a jump wire to get the water to it but it wont do it on its own why?
Hi\015\012\015\012\015\012Thanks for using FixYa. To start\015\012with check the water line attached to the back of the\015\012refrigerator fo ...
I have a Kenmore Trio, model number 596.76539500 about 5.5 yrs old. The top refrigerator is not cooling, but the bottom freezer appears to be working properly as it will freeze water in the icemaker and keep it frozen. The temp readout on the refrigerator indicates 72 degrees while the freezer is 0.
Hi,Check out these tips...they can help you figure out what is going wrong with your refrigerator and why it is not cooling ...
Kenmore 73502 / 73504 / 73509 Bottom Freezer Refrigerator
Kitchen aid superba ice maker not getting water. model ksrg25fkss16 icemaker is not getting water to unit. Water dispenser works looks like water line splits at a pump or something at the back or fridge. seems like water is in line but nothing at icemaker
Ge profile PSS26MGP side by side installed in Oct 2008. Background: on 1-03-2011 freeze-refer temps approx 13 and 48, apples in top deli-fresh drawer were frozen. Ice maker not making ice, minimal water going to icemaker. on 1-20-2011 temps still approx 13 and 48 and icemaker still not getting water. Unplugged the unit. 2-1-2011 Plugged unit in, changed water filter, ran icemaker diagnostic test, unit started up, ran fine, in a few hours temps were 0 and 34 and icemaker had water and was makin
The most common fridge \012"not cooling" problem is a frost \012free failure. Remove the access panel in the freezer section to expose the \012evaporator coils. If the coils in the freezer section get plugged up with frost, this frost will ...
The refrigerator is a Model frs26zseb purchased in 1997. It has worked well until now
The icemaker is not getting water.
I have replaced both the inlet valve and the icemaker.
All tubing has been checked and is open.
There is good water flow to the water dispenser and if I reverse the connections to the water inlet valve I have good water flow to the icemaker
Temperature in the freezer is between -5 and 10 F but the refrigerator rune constantly.
What is left to check?
Wow with a new water valve and a new ice maker and temps below 20 f in the ice box that puppy should drop ice. Add some water to the ice mold and see if tosses out a batch. Check your water pressure. Did you turn the water supply back on? Probably so ...
I have a Whirlpool model # ET1CHEXVB00 refridgerator. I just (few minutes ago) replaced the ice maker valve because water was no longer getting to the icemaker. Very shortly after I plugged the refridgerator back in and turned on the water, the icemaker went through one cycle and some water (mayber quarter cup) ran down the inside back of the freezer cabinet. Also one time recently (before I decided to replace the icemaker valve), I found several cups of water on the bottom of the freezer cab
Sounds like the fill tube at the ice maker is either out of alignment or has a crack in it.\012The water supply line from the water inlet valve \012enters the rear of the freezer and release ...
Whirlpool 21.0 cu. ft. Top Freezer Refrigerator with IceMagic Plus Ice Maker
I have a GE side by side Model: TFX27PRXD WW Serial: SR237995. No water is reaching the icemaker. Previously it would periodically begin to work then stop and start again. I replaced the water inlet valves for the icemaker and water dispenser, but the icemake still gets no water.
Is the freezer cold enough? Should be close to 10 degrees. Is there water or ice in the ice mold? If not put water in it and see if it dumps the ice after it’s frozen. If there is ice, lift the cut off arm and let it drop to see if it wi ...
GE (PSS26MSRSS) Side by Side Refrigerator
Kenmore freezer-on-top icemaker not getting water into icemaker. I replaced the water valve solenoid with a new one, but no change. There is no AC voltage at the solenoid terminals. The icemaker itself keeps rotating the teeth constantly, with the bail in the correct position. Could it be the thermostat in the icemaker? Can I replace just the thermostat without replacing the whole assembly?
First check the temperature in the freezer to make sure it is 8 degrees Fahrenheit or lower. If the freezer is too warm, the ice maker won't cycle properly.If the temperature is ok then the ice maker mold thermostat needs to be replaced. ...
I have a kenmore elite model # 106.56719500. My ice make and water denspinser are not working properly. Went to get some ice and the ice denspenser would not work, tried to get water and nothing happen. When I open the door to the freezer the ice denspenser started and so did the water. I tried unpluging the fridge and pulgging it back in, still the same. When I open the freezer and the ice maker and water start I pushed on the light switch in the freezer and everything stops but.
Kenmore side by side Mod#10657567790. No water to Icemaker. I am getting water to water disp. but none to icemaker. Changed out solenoid still no water to ice.
Hello. It sounds like the icemaker is bad. It is not the solenoid but the fact that the icemaker head is not requesting the water. ...
The model number that was found is FRT18PRA - this does not come up on your list of refrigerators. The freezer accumulated about 1 inch of ice within 48 hours and there was water in the refrigerator. There is an icemaker so I am thinking that the hose feeding the icemaker has sprung a leak but without being able to get to a site that has a diagram or owner's manual I can't find out. I turned off the water supply and there is less water in the refrigerator -- now there are just a few drops on
This fridge is not listed with an automatic icemaker.It originally came with ice trays.Is the Icemaker added on?Here is the diagram of the fridge... ...
I have a Kenmore Elite Refrigerator, Model No. 795.77573600. The ice and water dispenser give the error message Er 1F. In searching online it appears that this problem is related to the ice compartment cooling fan. I unplug the refrigerator for a few moments and then replug it and the panel lights up again and I can get water dispensed. However, after a while, the panel goes back to displaying the error message Er 1F and I can't even get water to dispense. Can you assist? Is this some kind
This is an error code for the icemaker fan motor. If the control does not see a signal coming back from the fan motor you will get this error code. Please see the image below from the service manual that explains the ER IF error code. ...
Kenmore Elite 22.4 cu. ft. Bottom Freezer Refrigerator with Adjusta Cube Ice Maker
My Kenmore refrigerator (model: 106.57713700)in-door icemaker stopped dispensing ice about two weeks ago. The auger was not turning in the unit, and I can assume that the auger motor is shot and will need replaced. This morning,water was pouring from the back of the refrigerator from the water entry point to the refrigerator. It appears that the water is not being "turned off" by the icemaking unit. Any thoughts? Can you give me a rough idea how much is usually charged to do repairs for problems
The water valve must be tested to be sure IT is the problem, and not the timer or control board in your unit.If its getting the signal to close - the valve is at fault. Typically this would be about $125 repair (depending on your location ...
I have a Kenmore Coldspot refrigerator/freezer. The freezer is on the top. Model # 72104107. I am getting water in the inside bottom of the refrigerator and I can not see where it is coming from. The water is all contained inside the refrigerator and it takes about 3 weeks to fill the bottom with water to where I need to through towels in the bottom and get it out before it overflows onto the floor. Any suggestions??
Solution is to Open the freezer compartment... \015\012- Locate screws on the back wall (from inside freezer compartment)\015\012- unscrew and open the back panel.\015\012- You will see a hole at the bottom which is the drain ...
I have a Kenmore side by side elite. I have installed a new ice maker. I can not get water into the ice maker. The extraction teeth rotate and I get water through the water port on the door but not into the icemaker. The unit has been installed for approx 30 hrs.
Usually happends that the solenoid (electric valve who opends when the ice maker calls for water) leaks and this water freezes up inside the filling tube for the ice maker , t he solenoid has to be replaced. ...
I have a Kenmore refrig/freezer, model 363.79262991. The ice maker has stopped working. I have traced that it is getting water to the water valve ASM, but nothing is getting through it. We checked the volts coming out of the power supply connected to this part and it was 27 volts. I have the following questions:
- Does the water valve ASM run on 27 volts, or is there something wrong with my power supply?
-If it does run on 27 volts, that would lead me to believe there is something wrong wi